A-1000 Americrete Concrete Stain
Description
Americrete Concrete Stain is a user friendly, water base acrylic
stain for concrete. This product penetrates the surface for a
tenacious bond. Available in 18 standard colors and 8 stain
pro colors, these colors can be mixed for unlimited selection.
Concrete Stain is used as a protective, decorative coloring
system over new and old, pigmented and non-pigmented
concrete, masonry and wood surfaces. The surface must be
sealed with one of Americrete’s sealers. This product can be
used on driveways, pool decks, architectural designs, natural
stone, stamped concrete, stucco, walkways, industrial floors,
kitchen floors, concrete block, exposed aggregate, brick,
precast concrete, tile, fencing, wood decks, Mexican pavers,
Americrete cements and anything that will accept a penetrating
stain. An Americrete sealer is to be used when heavy traffic or
vehicle traffic is expected. Call for Americrete sealer
recommendations.
Preparation of surface
Americrete Stain Pro will bond to properly cleaned and
porous concrete surfaces. Mechanical or chemical
abrasion may be necessary in order to achieve the proper
profile. Profile means that the concrete should feel rough,
like 80-100 grit sandpaper.
Existing Coated Floors
All existing coatings, sealers, curing agents and other
foreign materials must be removed by shot blast or
grinding equipment in order to reveal clean concrete.
Cleaning
If oil or greasy spots are present clean by scrubbing the
surface with A-100 Degreaser. Broom A-100 Degreaser
evenly over the entire surface. Allow the degreaser to
remain on the surface for approximately 30 minutes. Do a
final clean with TSP cleaner to insure A-100 is totally
removed. Power wash surface with a 3000 to 4000 psi
machine. Read A-100 Degreaser Specifications for full
details.
Vapor Transmition:
The surface should be tested to assure
that the vapor transmission is below 3.5 lbs. per 1000 sq. ft.
This can be measured by using a Calcium Chloride test kit.
Follow directions on the test kit.
Coverage Rate:
Concrete stain can be applied at
approximately 250-400 square feet per gallon depending on
the application procedure, surface porosity, and texture of the
surface.
Directions
Stir, do not shake, the product to ensure that the color is mixed
homogenously before application. Box same colors together in
a larger container to ensure color uniformity. Can be applied
by brush, roller, or Hudson sprayer. If using a Hudson sprayer,
use a soft bristle brush push broom to help penetration and
uniformity. Product may also be worked in with a rag or
sponge to add different effects while still wet.
Caution: Do not apply in direct sun on a hot day. Surface
temperature should not exceed 100oF. Do not apply in cold or
threatening weather such as heavy dew, fog, mist or rain is
forecasted within 24 hours. Do not apply if the surface
temperature is below 55oF.
Product Warranty/Liability Disclaimer
Since no control is exercised over product use,
AMERICRETE represents and warrants ONLY that the
products are of consistent quality within manufacturing
tolerances for a period of ONE year. NOTE: if Americrete
sealers are not used to seal the surface then there is NO
WARRANTY implied. Americrete sealers must be applied
to the substrate for Americrete to warranty material.
All sales are final. NO other oral or written representation
or statement of any kind, expressed or implied, now or
hereafter is authorized or warranted by AMERICRETE,
including those of marketability or fitness for a particular
purpose. Liability for breach of contract, negligence or on
any other legal basis is limited to the lesser cost of refund
or replacement of material proven to be defective.
AMERICRETE, will not be liable for special, incidental or
consequential damages, including for delays or lost profits.
There is no warranty for product installations, color
variations, product delamination or cracks in the surface
due to the substrate cracking. The end user shall
determine the suitability of the products for the intended
use and assumes all risks and liability in connection
therewith.
NOTE:
If litigation arises the party filing the complaint or
law suit will be responsible for all attorney fees and court
costs incurred by AMERICRETE, and all other costs
related to the investigation of the law suit and/or
complaint.
This warranty is effective August 1, 2007, and supersedes
any and all previous warranties, written or verbally
communicated Note: Americrete products are to be
applied only when surface temperatures are at 55oF or
higher, not to exceed 100oF. Do not apply when rain or
other precipitation is expected within 24 hours.